ACOUSTICAL RATED DOORS Bonded Construction
DESCRIPTION Flush Wood Doors with special sound retardant core. Tested and certified under the requirements of ASTM E90-87.

ITEM	SPECIFICATIONS
Maximum Size	4'0" x 8'0" Single Door
Thickness	1 3/4"
Stiles	1" laminated stiles with 1/2" minimum hardwood. Bonded to core. 1 3/8" stiles optional.
Rails	2 1/4" softwood. Hardwood as specified. Bonded to core.
Core	Particle board with special sound retardant core.
Adhesives	Type II Interior
Faces	All commercially available hardwood veneer species and high pressure plastic laminates.
STC Rating	Single door - STC 40 - STC 47 Communicating pair - STC 50
Openings for Lights and Louvers	Glass lights are not recommended. Ratings listed above are based on test of flush doors and any glass light (using acoustical rated glass) will reduce overall performance. Louvers are not permitted. Acoustical doors in pairs must have solid mullion fully grouted with gasketing identical to single doors.
Prefitting	May be prefit to net sizes as specified.
Machining	Must be factory machined for hardware as specified.

ARCHITECTURAL
1 1/2 HOUR B LABEL FIRE DOOR
Mineral Core

DESCRIPTION

Architectural Mineral Core Fire Doors are intended for use where 90 minute fire barriers are required. These doors are listed by Warnock Hersey International and bear a W.H.I. Label.

ITEM	SPECIFICATIONS
Maximum Size	4'0" x 9'0" single swing 6'0" x 7'0" regular pair 8'0" x 8'0" regular pair with surface vertical rod both leaves
Thickness	1 3/4"
Stiles	Latch Stile: 3/4" SLM Hinge Stile: 1" total. 1/2" SLM, 1/2" composition material.
Rails	Top Rail 3/4" SLM Bottom Rail 1 3/4" SLM
Core	Mineral Core
Adhesives	Type II Interior
Faces	All commercially available hardwood veneer species and high pressure plastic laminates.
Lights	100 sq. in. maximum 1/4" labeled glazing material (wire glass) installed in listed glazing frame, not nearer than 6" to any edge of the door. Maximum 10" width, minimum 3" width, and maximum 33" length. U.L. listed viewers not larger than 1" diameter. (All dimensions to visible glass).
Prefitting	May be prefit to net sizes as specified.
Machining	Must be factory machined for hardware as specified or by an authorized distributor, licensed to machine fire rated wood doors under label service.
Edge Guards	Minimum 20 gauge steel channels with overlapping astragals are required on meeting stiles of pairs. When surface vertical rod exit devices are used overlapping astragal must be omitted.

ARCHITECTURAL 1 HOUR B LABEL
FIRE DOOR
Mineral Core

DESCRIPTION

Architectural Mineral Core Fire Doors are intended for use where 60 minute fire barriers are required. These doors are listed by Warnock Hersey International and bear a W.H.I. Label.

ITEM	SPECIFICATIONS
Maximum Size	4'0" x 9'0" single swing 3'0" x 10'0" single swing 8'0" x 9'0" regular pairs 8'0" x 8'0" double egress pairs
Thickness	1 3/4"
Stiles	Latch Stile: 3/4" SLM Hinge Stile: 1" SLM
Rails	Top Rail 3/4" SLM Bottom Rail 1 3/4" SLM
Core	Mineral Core
Adhesives	Type II Interior
Faces	All commercially available hardwood veneer species and high pressure plastic laminates.
Lights	100 sq. in. maximum 1/4" labeled glazing material installed in listed glazing frame, not nearer than 6" to any edge of the door. Maximum 10" width, minimum 3" width, and maximum 33" length. U.L. listed viewers not larger than 1" diameter. (All dimensions to visible glass).
Louvers	576 sq. in. maximum fusible link (160 degrees) louver with no nearer than 6" to any edge door.
Prefitting	May be prefit to net sizes as specified.
Machining	Must be factory machined for hardware as specified or by as authorized distributor, licensed to machine fire rated wood doors under label service.
Edge Guards	Minimum 20 gauge steel channels with overlapping astragals are required on meeting stiles of pairs. When surface vertical rod exit devices are used overlapping astragal must be omitted.

ARCHITECTURAL 3/4 HOUR C LABEL FIRE DOOR 
Mineral Core

DESCRIPTION Architectural Mineral Core Fire Doors are intended for use where 45 minute fire barriers are required. These doors are listed by Warnock Hersey International and bear a W.H.I. Label.

 

ITEM	SPECIFICATIONS
Maximum Size	4'0" x 9'0" single swing 3'0" x 10'0" single swing 8'0" x 9'0" regular pairs 8'0" x 8'0" double egress pairs
Thickness	1 3/4"
Stiles	Latch Stile: 3/4" SLM Hinge Stile: 1" SLM
Rails	Top Rail 3/4" SLM Bottom Rail 1 3/4" SLM
Core	Mineral Core
Adhesives	Type II Interior
Faces	All commercially available hardwood veneer species and high pressure plastic laminates.
Lights	1296 sq. in. maximum 1/4" labeled glazing material installed in listed glazing frame, not nearer than 6" to any edge of the door. Maximum 30" width, minimum 3" width, and maximum 54" length. U.L. listed viewers not larger than 1" diameter. (All dimensions to visible glass).
Louvers	576 sq. in. maximum fusible link (160 degrees) louver with no nearer than 6" to any edge door.
Prefitting	May be prefit to net sizes as specified.
Machining	Must be factory machined for hardware as specified or by an authorized distributor, licensed to machine fire rated wood doors under label service.
Edge Guards	Minimum 20 gauge steel channels with overlapping astragals are required on meeting stiles of pairs. When surface vertical rod exit devices are used overlapping astragal must be omitted.

ARCHITECTURAL 20 MINUTE FIRE DOOR
Bonded Construction

DESCRIPTION Architectural 20 Minute Rated Fire Doors, when installed in approved assemblies, provide 20 minute protection as required by all existing Building Codes. These doors are listed by both Warnock Hersey International (W.H.I.) and California State Fire Marshall (C.S.F.M.) Meets or exceeds the following industry standards: Current ANSI / NWWDA I.S. 1A, W.I.C. Section 20, and A.W.I. Section 1300 when specified.

 

ITEM	SPECIFICATIONS
Maximum Size	Single Swing   Pair-Regular Up to 3'0" x 10'0"   8'0" x 9'0" or 4'0" x 9'0"   Double Egress 3'0" x 10'0" with   Up to 8'0" x 8'0" rabetted transom   Dutch
Transom Size	3'0" x 1'0" 3'0" x 3'4" with SLM meeting rails
Thickness	1 3/4"
Stiles	1 1/8" 2-ply hardwood bonded to core. 1 3/8" hardwood optional.
Rails	1 1/8" minimum, Bonded to core.
Core	Particle Board - Lumber Core Optional
Adhesives	Type II Interior, Type I Exterior
Faces	All commercially available hardwood veneer species and high pressure plastic laminates.
Lights	1296 sq. in. maximum with no dimension exceeding 40". Vision lights may not be installed nearer than 6" to any edge of the door. Viewers up to 1" diameter may be installed. (All dimensions to visible glass.)
Prefitting	May be prefit to net sizes as specified.
Machining	May be factory machined for listed hardware as specified for 20 minute rated doors.
Edge Guards	Minimum 20 gauge steel channels are required on meeting stiles of pairs. Not required on pairs of doors with SLM stiles.

ARCHITECTURAL SOLID CORE DOOR
Lumber Core

DESCRIPTION Architectural Lumber Core Door, is manufactured with low density, kiln-dried, edge-glued wood blocks, providing versatile application of surface mounted hardware. Meets or exceeds the following industry standards: Current ANSI / NWWDA I.S. 1A, W.I.C. Section 20, and A.W.I. Section 1300 when specified.

 

ITEM	SPECIFICATIONS
Maximum Size	4'0" x 10'0"
Thickness	1 3/8" or 1 3/4"
Stiles	1 3/8" 2-ply hardwood bonded to core. 1 3/8" hardwood optional.
Rails	1 1/8" minimum, Bonded to core.
Core	One species of edge-glued, low-density, kiln-dried wood blocks of random lengths with well staggered joints. Bonded to stiles and rails.
Adhesives	Type II Interior, Type I Exterior
Faces	All commercially available hardwood veneer species and high pressure plastic laminates.
Opening for Lights and Louvers	Total area of openings not to exceed 40% of door area or 50% of door height; must be a minimum of 5" from edges of door.
Prefitting	May be prefit to net sizes as specified.
Machining	May be factory machined for hardware as specified.
Other Detail Work	Metal louvers and light stops as specified. Wood louvers and light stops to match faces. Aluminum channels recommended on bottom rails of exterior doors.

ARCHITECTURAL SOLID CORE DOOR
Particle Board Core

DESCRIPTION Architectural Partical Board Bonded Core construction provides maximum straightness and stability. Telegraphing is eliminated by manufacturing with a stree free core of uniform thickness. Meets or exceeds the following industry standards: Current ANSI / NWWDA I.S. 1A, W.I.C. Section 1300 when specified.

 

ITEM	SPECIFICATIONS
Maximum Size	4'0" x 10'0"
Thickness	1 3/8" or 1 3/4"
Stiles	1 1/8" 2-ply hardwood bonded to core. 1 3/8" hardwood optional.
Rails	1 1/8" minimum, Bonded to core.
Core	Particle Board. Meets or exceeds requirements of ANSI A208.1 and CS236-66.
Adhesives	Type II Interior, Type I Exterior
Faces	All commercially available hardwood veneer species and high pressure plastic laminates.
Opening for Lights and Louvers	Total area of openings not to exceed 40% of door area or 50% of door height; must be a minimum of 5" from edges of door.
Prefitting	May be prefit to net sizes as specified.
Machining	May be factory machined for hardware as specified.
Other Detail Work	Metal louvers and light stops as specified. Wood louvers and light stops to match faces. Aluminum channels recommended on bottom rails of exterior doors.